SkyLink SC-100 Manual do Utilizador Página 6
- Página / 51
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
1. Position the transmitter be-
side the door/window frame on
the wall using either two sided
tape or screws. If you are using
screws, first pry off the back plate
with a small screwdriver and
screw the back plate into posi-
tion using the template. Then click
the transmitter on to the back
plate now mounted on the wall.
4. Attach the unit to the wall. If hanging the unit,
insert two screws using the template provided.
If screwing the back directly to the wall, take the
back plate right off by prying apart one hinge.
Use as much force as needed. The plastic hinge
will not break.
5. Using the template, attach the backplate on to
the wall with 4 screws.
6. Mount the Control Panel on the backplate. Insert
one hinge into the hole, then twist the other hinge
into position.
7. Firmly close the case.
8. Plug the AC adapter into a power outlet. The red
AC PWR light will be on.
INSTALLING THE DOOR/WINDOW SENSOR (WT-433)
It is recommended to install one sensor on your front door and the other on
your back door.
Each contact sensor has 4 parts:
–
7
–
INSTALLATION
Transmitter Magnetic Switch Magnet Spacers
–
8
–
INSTALLATION
2. Position the magnetic switch connected to
the transmitter on the door/window frame.
3. Position the magnet on the door beside the
magnetic switch. They should be no more
than 1 cm (3/8 inch) apart. When the door/
window is closed, the magnets are in contact.
When the door/window is opened, contact is
broken and the transmitter sends a signal to
the Control Panel to activate the chime or
alarm.
INSTALLING THE MOTION SENSOR (PS-434A)
Insert 9V alkaline battery to the sensor
Insert a 9V alkaline battery to the motion sensor.
The sensor requires a warm up time of approx.
45 seconds before it can function properly. After
powering up the sensor, face it to the wall where
no motion will be detected. After 45 seconds, the
sensor is ready.
SENSOR SENSITIVITY
The sensitivity of the motion sensor is adjust-
able. Change the setting by placing the connector
on either the ”High” or “Low” position. When the
sensitivity is set to “Low”, more movement is
required to trigger the sensor. It is recommended
to set the sensitivity to “Low” and perform a “Walk
Test” (Described in later Section). If the walk test
result is satisfied, the sensitivity does not require
to be adjusted further. If the walk test result
shows the sensitivity is too low, then you can change
the sensitivity setting to “High”. Please perform
the walk test after changing the sensitivity setting.
MOUNTING
A ball-head joint is necessary to mount the
sensor at a desire location. A height of 5-6 ft is
recommended, depending on your application.
Once a location is selected, mount the ball-head
joint to this location by screws provided, (see
diagram 1). Once the ball-head joint is mounted to
the wall, slide the back of the sensor into the ball-
head joint (see diagram 2). The mounting angle
can be adjusted. Please refer to Section “Walk
Test” to determine the best mounting angle.
Sensitivity Connectors on Motion Sensor
Diagram 1
Diagram 2
Note: High=1, Low=2, Default is 1
- Total Protection Alarm System 1
- Système de Sécurité sans fil 1
- Total Protection Alarm 2
- PACKAGE CONTENTS 4
- OVERVIEW 4
- TESTING YOUR SYSTEM 7
- LIGHTS AND SOUNDS 8
- STANDARD PROGRAMMING 8
- KEYCHAIN TRANSMITTER (4B-434) 10
- PASSWORDS 10
- ADVANCED PROGRAMMING 11
- SUMMARY OF ARMING SEQUENCES 14
- BATTERY MAINTENANCE 14
- ADDITIONAL ACCESSORIES 16
- Système de Sécurité 18
- Système de sécurité sans fil 19
- CONTENU DE L'EMBALLAGE 20
- VUE D'ENSEMBLE 20
- SÉCURITÉ A DOMICILE 21
- INSTALLATION 21
- TESTER VOTRE SYSTÈME 23
- LUMIÈRES ET SONS 24
- PROGRAMMATION DE BASE 25
- (4B-434) 26
- MOTS DE PASSE 27
- PROGRAMMATION AVANCÉE 28
- PILE DU PANNEAU DE COMMANDE 31
- ENTRETIEN DE LA PILE 32
- ACCESSOIRES ADDITIONNELS 33
- Sistema de Alarma con 35
- Protección Total 35
- MODELO: SC-100 36
- CONTENIDO DEL CONJUNTO 37
- DESCRIPCIÓN 37
- HOGAR / NEGOCIO 38
- INSTALACIÓN 38
- PRUEBA DE SU SISTEMA 40
- LUCES Y SONIDOS 41
- PROGRAMACION ESTANDARD 42
- TRANSMISÓR A LLAVERO (4B-434) 43
- PALABRAS DE PASO 44
- PROGRAMACIÓN AVANZADA 45
- MANTENIMIENTO DE LAS BATERIAS 49
- ACCESORIOS ADICIONALES 50
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso SkyLink SC-100
(2 páginas)JVC HR-XVC29UJ manuales
Manuales del propietario y guías del usuario para Reproductores de dvd JVC HR-XVC29UJ.
Ofrecemos 1 manuales en pdf JVC HR-XVC29UJ para descargar gratis por tipos de documentos: Manual de usuario
Comentários a estes Manuais