SkyLink HA-400 Manual do Utilizador descarregar pdf (Página 2)

The sensor must be programmed to the Household Alert

Long Range

Receiver before they can communication. You may program the sensor

to one of the 4 zones. Follow the instructions below;

1. Plug in an AC adapter to the receiver.

2. Power up the Receiver unit. The green LED will be on indicating it

is turn on.

3. Open the back cover and there is a learn button. Press and hold

this learn button for 5 seconds, until both g

reen LED and zone 1

red LED

You may now release the learn button.

4. If you would like to program the sensor to zone 1, activate the

sensor while the zone 1 red LED is

Activate the Sensor

by separating the magnetic contact from the sensor.

5. If you would like to program the sensor to other zones, press the

learn button again, until the red LED

at the zone you want

to program the sensor to, then activate the sensor.

6. Once the sensor is programmed, the green LED will be steadily on

and none of the red zone LEDs will be on.

Note: Each zone can program up to 4 sensors. If you try to program a

sensor into a zone, the programmed sensor will be erased.

Plug in the adapter to the receiver

4. PROGRAMMING WINDOW/DOOR SENSOR

Learn Button

Separate the magnet from

the sensor, Receiver zone LED

stops

After learning the sensor to the Receiver unit, you may test the com-

munication by placing the magnet beside the sensor (where the red

marking is) and remove the magnet from the sensor.

When the magnetic is closed, the

receiver will not beep.

When the magnetic contact is broken (open),

the receiver will beep and zone LED will

1) Zone LED of this sensor will h.

2) Beeping according to the zone number [Operating mode is set to

“Alert”]. 1 beep for zone 1, 2 beeps for zone 2 and etc, until the

magnetic contact is closed.

You cannot erase a

sensor. You must erase all sensors from

the receiver, then program the ones you would like to keep. To erase all

the sensors from the receiver:

1. Remove the adapter from the receiver.

2. Open the back cover, press and hold the learn button. Do not release

the learn button until step 4.

3. While holding onto the learn button, plug in the adapter to the receiver.

4. You may release the learn button when the LEDs on the rec

eiver are

on.

5. You have erased all sensors from the receiver.

5. WINDOW/DOOR SENSOR INSTALLATION

Sensor

Magnet

"Red Marking"

on the side

"Red Marking"

on the side

The transmitters should be mounted on the door frame or window frame

by double sided tape. The magnet should be mounted on the door or

window by either double sided tape or screws. Make sure the magnet is

aligned with the red marking on the transmitter. If the surface of the frame

enough, double-sided foam tape is otherwise, it is

recommended to screw the mounting plate to the frame, then apply

double sided tape. After mounting the sensor, if the Skylink logo is

inverted, remove the front cover and rotate it so the Skylink logo is in the

upright position.

Mounting plate

and screws (optional)

Double-sided

foam tape

Sensor

6. OPERATION

There are 3 di

operating modes for the Household Alert

Long

Range Receiver.

1) Alert - Beeps when a sensor is activated, corresponding zone LED

will also

2) Alarm - Sounds an alarm when a sensor is activated, corresponding

zone LED will also

- No audio sound will be emitted when sensor is activated.

Zone LED will

to indicate the activated

sensor.

To select the operating mode, place the

slide switch on the side at the desired setting:

OFF - No Audio

ALERT - Alert Mode

ALARM - Alarm Mode

Alert

When motion is detected in the monitored area, the sensor will send a

signal to the receiver. It will beep and the corresponding zone red LED

will

for 15 seconds.

If the sensor is set to zone 1, zone 1 red LED on the receiver will

and the receiver will emit a continuous “single beep”, i.e. “beep” pause,

“beep”, pause….. etc.

If the sensor is set to zone 4, zone 4 red LED will

and the receiver

will emit a continuous “4 beeps”, i.e. “beep beep beep beep” pause

“beep beep beep beep” pause ……etc.

By the number of beeps emitted by the receiver, user can identify which

zone is triggered.

Test Sensor

Erasing a sensor

Operation

Page 2 of 3

1 2 3

Comentários a estes Manuais

Sem comentários

SkyLink HA-400 Manual do Utilizador Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com não SkyLink HA-400